Clearone-comm PSR1212 Instrukcja Użytkownika Strona 73
- Strona / 145
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
67
Operation ~ Utilities
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
4. Repeat steps 1–3 to select the second second unit, site, or file for
comparison.
When you click Open, G-Ware automatically compares information from the
selected items and displays a table of parameters which differ (note that the
actual differences are not displayed at this point). This process can take a
minute or two.
5. To view the difference(s) between two sources on a single parameter, select
the row in the table you want to examine, then click Preview. This opens
the Print Preview window, which shows what the differences are.
Figure 5.6. Document Compare Utility showing two PSR1212 sites. The items
listed in the Site 1 and Site 2 columns show where the differences are found.
Figure 5.5. Open window
- PSR1212 Digital Matrix Mixer 1
- PSR1212 Installation and 2
- Operation Manual 2
- ClearOne Part No. 800-155 2
- 001 Jan 2007(Rev. 7.1) 2
- Table of Contents 3
- CHAPTER 1: Introduction 7
- New Features 8
- Unpacking 10
- Front panel 10
- Controls and Connections 10
- Rear panel 11
- Networking 13
- Expansion bus 13
- CHAPTER 2: Installation 15
- To connect the unit 16
- Expansion bus connections 17
- Networking Units 17
- Device IDs 18
- Mixer mode 18
- LCD menu tree 19
- LCD Programming 19
- System menu 20
- RS-232 menu 21
- Meter menu 22
- Inputs menu 23
- Outputs menu 24
- = Meter Reference Point 25
- CHAPTER 3: System 27
- Configuration 27
- Creating Floppy Disk Copies 28
- To install G-Ware 28
- Installing G-Ware 28
- Site Setup 29
- Creating a new site 29
- Adding a PSR1212 30
- Configuring Unit Properties 31
- Flow Screen 33
- G-Ware Screens 33
- Status bar 34
- Copying and pasting settings 34
- Safety Mute 34
- Matrix Screen 35
- Expansion bus O–Z routing 36
- Process A–H routing 36
- Cross point attenuation 36
- Audio Routing 36
- Matrix report 37
- Inputs 1–8 38
- Inputs and Outputs 38
- Active Filter 39
- To configure filters 41
- Activation 41
- Decay Rate 43
- PA Adapt and AEC Reference 43
- Figure 3.31 44
- Virtual Reference 44
- Gating Group Select 45
- Pre Gain 47
- Post Gain 47
- Post Processing 47
- Post Gating 47
- Inputs 9–12 48
- Outputs 1–12 50
- Max adjust 51
- Min adjust 51
- Figure 3.42 51
- Output gain adjust 51
- From Expansion Bus O–Z 52
- To Expansion Bus O–Z 52
- Expansion Buses 52
- Processing A–H 53
- Processing 53
- Cmprs (compressor) 54
- Figure 3.49. Delay window 57
- Figure 3.50. Process 58
- CHAPTER 4: Advanced 59
- Preset Configuration pane 60
- Figure 4.4. Preset Mask 61
- Control/Status B 61
- To create a preset 63
- Storage space 63
- Running presets 64
- Room combining example 65
- Creating macros 67
- Figure 4.16 Macro Name window 68
- Figure 4.14 68
- Macro Editor button 68
- Editing macros 69
- Running macros 70
- CHAPTER 5: Operation 71
- Document Compare Utility 72
- Operation ~ Utilities 73
- Copying settings 74
- Print Reports 75
- GFirm Firmware Utility 76
- G-Ware Switcher 78
- Copy and paste settings 79
- Message Log 79
- Gate View 79
- Monitoring Views 79
- Meter Views 80
- CHAPTER 6: Control 81
- XAP IR Remote 82
- Remote Builder 82
- ClearOne Control Panels 83
- Control ~ Remote Builder 84
- To program the Volume panel 84
- To program the Select panel 85
- Remote Modem Access 86
- Serial commands 86
- RS-232 Port 86
- Command strings 87
- APPENDICES 89
- Appendix B: Pinouts 90
- Control/Status connectors 91
- Control/Status B port pinout 92
- Set connector pinout 93
- Line connector pinout 93
- Appendix C: Control Panel 94
- Connecting the Control Panel 94
- Control Panel Assembly 95
- Dimensions (both 95
- Appendix D: Accessories 97
- Conventions 98
- Command structure 98
- Appendix E: Serial Commands 98
- Groups and channels 99
- Type and device IDs 99
- Meter type definitions 100
- Serial command error codes 100
- PSR1212 Serial commands 101
- AMBLVL - Ambient Level Adjust 103
- AAMB - Adaptive Ambient Mode 103
- AGC - Automatic Gain Control 103
- BAUD - Baud Rate 104
- COMPRESS - Compressor Adjust 105
- COMPSEL - Compression Select 105
- DECAY - Decay Adjust 106
- DELAY - Delay Adjust 106
- DELAYSEL - Delay Select 106
- DFLTM - Default Meter 107
- DID - Device ID 107
- FILTER - Filter Adjust 108
- FILTSEL - Filter Select 109
- FLOW - Flow Control 109
- FMP - First Mic Priority Mode 109
- FPP - Front Panel Passcode 110
- GAIN - Gain Adjustment 110
- GATE - Gate Status 111
- GHOLD- Gate Hold Time Adjust 111
- GMODE - Gating Mode 112
- GOVER - Gating Override 112
- GRATIO - Gate Ratio Adjust 112
- GREPORT - Gate Report 113
- GRPSEL - Gating Group Select 113
- LABEL - Label 113
- LFP - Lock Front Panel 114
- LMO - Last Mic On Mode 114
- LOCK - Preset and Macro Lock 114
- LVL - Level 115
- LVLREPORT - Level Report 116
- LVLRRATE - Level Report Rate 116
- MAX - Maximum Gain Setting 117
- MDMODE - Modem Mode 118
- MIN - Minimum Gain Setting 118
- Example: 119
- MLINE - Mic/Line Adjust 120
- MPASS - Modem Password 120
- MTRX - Matrix 121
- MUTE - Mute 122
- OFFA - Off Attenuation Mode 122
- PAA - PA Adaptive Mode 123
- PP - Phantom Power 123
- PRGSTRING - Program String 124
- RAMP – Ramp Gain Adjustment 125
- SERECHO - Serial Echo 126
- SERMODE - Serial Mode 126
- SFTYMUTE - Safety mute 127
- SIGGEN - Signal Generator 127
- STRING - String Execution 128
- TOUT - Time Out Select 128
- UID - Unit ID 129
- VER - Version 129
- Appendix F: Warranty 130
- FCC Part 15 Compliance 132
- Safety Information 132
- Appendix G: Compliance 132
- Glossary 133
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji