Clearone-comm PSR1212 Instrukcja Użytkownika Pobierz pdf (Strona 15)

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

The PSR1212 is designed for easy installation and setup. All connections are made

through rear-panel connectors. This chapter provides instructions on making

hardware connections, creating an expansion bus network, assigning device ID

numbers, selecting the mixer mode, and using the front panel LCD menus.

The diagram below illustrates the typical connections that are made for a PSR1212

system.

CHAPTER 2: Installation

Hardware Setup

ClearOne

Figure 2.1. PSR1212 installation diagram

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 144 145

PSR1212 Digital Matrix Mixer 1
PSR1212 Installation and 2
Operation Manual 2
ClearOne Part No. 800-155 2
001 Jan 2007(Rev. 7.1) 2
Table of Contents 3
CHAPTER 1: Introduction 7
New Features 8
Unpacking 10
Front panel 10
Controls and Connections 10
Rear panel 11
Networking 13
Expansion bus 13
CHAPTER 2: Installation 15
To connect the unit 16
Expansion bus connections 17
Networking Units 17
Device IDs 18
Mixer mode 18
LCD menu tree 19
LCD Programming 19
System menu 20
RS-232 menu 21
Meter menu 22
Inputs menu 23
Outputs menu 24
= Meter Reference Point 25
CHAPTER 3: System 27
Configuration 27
Creating Floppy Disk Copies 28
To install G-Ware 28
Installing G-Ware 28
Site Setup 29
Creating a new site 29
Adding a PSR1212 30
Configuring Unit Properties 31
Flow Screen 33
G-Ware Screens 33
Status bar 34
Copying and pasting settings 34
Safety Mute 34
Matrix Screen 35
Expansion bus O–Z routing 36
Process A–H routing 36
Cross point attenuation 36
Audio Routing 36
Matrix report 37
Inputs 1–8 38
Inputs and Outputs 38
Active Filter 39
To configure filters 41
Activation 41
Decay Rate 43
PA Adapt and AEC Reference 43
Figure 3.31 44
Virtual Reference 44
Gating Group Select 45
Pre Gain 47
Post Gain 47
Post Processing 47
Post Gating 47
Inputs 9–12 48
Outputs 1–12 50
Max adjust 51
Min adjust 51
Figure 3.42 51
Output gain adjust 51
From Expansion Bus O–Z 52
To Expansion Bus O–Z 52
Expansion Buses 52
Processing A–H 53
Processing 53
Cmprs (compressor) 54
Figure 3.49. Delay window 57
Figure 3.50. Process 58
CHAPTER 4: Advanced 59
Preset Configuration pane 60
Figure 4.4. Preset Mask 61
Control/Status B 61
To create a preset 63
Storage space 63
Running presets 64
Room combining example 65
Creating macros 67
Figure 4.16 Macro Name window 68
Figure 4.14 68
Macro Editor button 68
Editing macros 69
Running macros 70
CHAPTER 5: Operation 71
Document Compare Utility 72
Operation ~ Utilities 73
Copying settings 74
Print Reports 75
GFirm Firmware Utility 76
G-Ware Switcher 78
Copy and paste settings 79
Message Log 79
Gate View 79
Monitoring Views 79
Meter Views 80
CHAPTER 6: Control 81
XAP IR Remote 82
Remote Builder 82
ClearOne Control Panels 83
Control ~ Remote Builder 84
To program the Volume panel 84
To program the Select panel 85
Remote Modem Access 86
Serial commands 86
RS-232 Port 86
Command strings 87
APPENDICES 89
Appendix B: Pinouts 90
Control/Status connectors 91
Control/Status B port pinout 92
Set connector pinout 93
Line connector pinout 93
Appendix C: Control Panel 94
Connecting the Control Panel 94
Control Panel Assembly 95
Dimensions (both 95
Appendix D: Accessories 97
Conventions 98
Command structure 98
Appendix E: Serial Commands 98
Groups and channels 99
Type and device IDs 99
Meter type definitions 100
Serial command error codes 100
PSR1212 Serial commands 101
AMBLVL - Ambient Level Adjust 103
AAMB - Adaptive Ambient Mode 103
AGC - Automatic Gain Control 103
BAUD - Baud Rate 104
COMPRESS - Compressor Adjust 105
COMPSEL - Compression Select 105
DECAY - Decay Adjust 106
DELAY - Delay Adjust 106
DELAYSEL - Delay Select 106
DFLTM - Default Meter 107
DID - Device ID 107
FILTER - Filter Adjust 108
FILTSEL - Filter Select 109
FLOW - Flow Control 109
FMP - First Mic Priority Mode 109
FPP - Front Panel Passcode 110
GAIN - Gain Adjustment 110
GATE - Gate Status 111
GHOLD- Gate Hold Time Adjust 111
GMODE - Gating Mode 112
GOVER - Gating Override 112
GRATIO - Gate Ratio Adjust 112
GREPORT - Gate Report 113
GRPSEL - Gating Group Select 113
LABEL - Label 113
LFP - Lock Front Panel 114
LMO - Last Mic On Mode 114
LOCK - Preset and Macro Lock 114
LVL - Level 115
LVLREPORT - Level Report 116
LVLRRATE - Level Report Rate 116
MAX - Maximum Gain Setting 117
MDMODE - Modem Mode 118
MIN - Minimum Gain Setting 118
Example: 119
MLINE - Mic/Line Adjust 120
MPASS - Modem Password 120
MTRX - Matrix 121
MUTE - Mute 122
OFFA - Off Attenuation Mode 122
PAA - PA Adaptive Mode 123
PP - Phantom Power 123
PRGSTRING - Program String 124
RAMP – Ramp Gain Adjustment 125
SERECHO - Serial Echo 126
SERMODE - Serial Mode 126
SFTYMUTE - Safety mute 127
SIGGEN - Signal Generator 127
STRING - String Execution 128
TOUT - Time Out Select 128
UID - Unit ID 129
VER - Version 129
Appendix F: Warranty 130
FCC Part 15 Compliance 132
Safety Information 132
Appendix G: Compliance 132
Glossary 133

Komentarze do niniejszej Instrukcji

Brak uwag

Clearone-comm PSR1212 Instrukcja Użytkownika Strona 15

Komentarze do niniejszej Instrukcji